Skip to content
Lychee Documentation
  • Home
  • About us
  • Contact us
Lychee Documentation
  • Home
  • About us
  • Contact us

J3D-Tech’s Guide to Resin Printing, Beginners - Advanced

  • Lychee Documentation
  • J3D-Tech’s Guide to Resin Printing, Beginners - Advanced

Introduction (1)

  • Good to know...
View all articles from this section

Printer Installation (3)

  • Levelling the Bed
  • Resin Mixing and FEP Squeegee
  • VAT Clean after a failed print
View all articles from this section

Printer Calibration (8)

  • Build Plate Calibration
  • Normal Layer Calibration
  • Burn-in-Layers / Bottom Layers Calibration
  • Two Stages Motion Control (TSMC) Calibration
  • Slice and Export Test Files
  • Prep your 3D Printer
  • Boxes of calibration
  • Calibrated resin profiles
View all articles from this section

Print Settings (10)

  • Two Step Motion Control (TSMC)
  • Anti-aliasing
  • Rafts
  • Model Sizes
  • Model Orientation
  • Introduction to Supporting
  • Advanced Supporting
  • Hollowing
  • Printing on the Plate
  • The truth about 90% of Failures
View all articles from this section

Post-Processing (10)

  • Video demo
  • Build Plate Removal
  • First Clean
  • 2nd Clean
  • 3rd Clean
  • Support Removal
  • 4th Clean
  • Final Dry
  • Final Cure
  • Can you Over Cure resin 3D prints?
View all articles from this section

Cleanup and Disposal (4)

  • Trash
  • Cleaning your FEP
  • Emptying and Removing The Vat
  • Clean your LCD
View all articles from this section

Troubleshooting Print Failures (7)

  • Layer Lines
  • Volcanoes
  • Just the supports
  • Split-Rafts
  • Flat rafts and/or Supports stop printing. 
  • Nothing on the Build Plate 
  • Half of the prints stuck to the Build Plate
View all articles from this section

Safety (1)

  • Mandatory equipment
View all articles from this section

My recommended items for 3D printing (9)

  • My Favorite Resin
  • Heating
  • Resin Printer Cleaning
  • Resin Printer Maintenance
  • Printed Model Post Processing
  • Consumables
  • My version of a Wash Station
  • Power
  • Focus
View all articles from this section

Ressources / Assets (1)

  • Manufacturer's Resin Profiles
View all articles from this section

Thank You ! (1)

  • Thank You !
View all articles from this section
  • Introduction
    • Good to know...
  • Printer Installation
    • Levelling the Bed
    • Resin Mixing and FEP Squeegee
    • VAT Clean after a failed print
  • Printer Calibration
    • Build Plate Calibration
    • Normal Layer Calibration
    • Burn-in-Layers / Bottom Layers Calibration
    • Two Stages Motion Control (TSMC) Calibration
    • Slice and Export Test Files
    • Prep your 3D Printer
    • Boxes of calibration
    • Calibrated resin profiles
  • Print Settings
    • Two Step Motion Control (TSMC)
    • Anti-aliasing
    • Rafts
    • Model Sizes
    • Model Orientation
    • Introduction to Supporting
    • Advanced Supporting
    • Hollowing
    • Printing on the Plate
    • The truth about 90% of Failures
  • Post-Processing
    • Video demo
    • Build Plate Removal
    • First Clean
    • 2nd Clean
    • 3rd Clean
    • Support Removal
    • 4th Clean
    • Final Dry
    • Final Cure
    • Can you Over Cure resin 3D prints?
  • Cleanup and Disposal
    • Trash
    • Cleaning your FEP
    • Emptying and Removing The Vat
    • Clean your LCD
  • Troubleshooting Print Failures
    • Layer Lines
    • Volcanoes
    • Just the supports
    • Split-Rafts
    • Flat rafts and/or Supports stop printing. 
    • Nothing on the Build Plate 
    • Half of the prints stuck to the Build Plate
  • Safety
    • Mandatory equipment
  • My recommended items for 3D printing
    • My Favorite Resin
    • Heating
    • Resin Printer Cleaning
    • Resin Printer Maintenance
    • Printed Model Post Processing
    • Consumables
    • My version of a Wash Station
    • Power
    • Focus
  • Ressources / Assets
    • Manufacturer's Resin Profiles
  • Thank You !
    • Thank You !
  • Home
  • About us
  • Contact us

Mango3D

©2025 Mango3d.io. All right reserved.